Liquid Electric Stirrer

The liquid electric stirrer drives the stirring paddle to rotate through a motor, generating forced convection in the liquid to achieve mixing. It is used for operations such as dissolution, emulsification, and homogenization in laboratories, and is suitable for sample preparation in industries such as chemical engineering, food, and pharmaceuticals.
Selection
When selecting, consider the compatibility of the container material and volume with the stirring power. For viscous liquids, a high-torque motor is required. For corrosive media, stainless steel or polytetrafluoroethylene blades should be used. If speed adjustment is needed, pay attention to the motor type and control precision. For long-term use, focus on the motor's heat dissipation and the sealing structure of the bearings.

Terms

Standards

Instruments

Adopt electronic voltage regulation circuit without electric shock, Temperature range environment temperature to 380 ℃, can work continuously, large heating area and no open flame design, avoid bumping Glass ware.

$ 123.00

Electric lift Travel 400mm, speed range 300~ 6000rpm, frequency conversion electromechanical operation quiet noise, suitable for laboratory liquid materials dispersed stirring.

$ 1752.00

Rotation speed 3000rpm, maximum linear speed 33m/s, high dispersion efficiency, strong material shear force, the formation of uniform suspension effect, safe and convenient operation, electric lifting fast fixed sealing barrel.

$ 2676.00

Rotation speed up to 3000rpm, linear speed up to 33m/s, using electric lifting and double-end sealing structure, to achieve efficient dispersion and vacuum defoaming, suitable for viscosity ≤ 25000cps materials.

$ 3193.00

With electric and magnetic dual stirring function, Temperature range to 100 ℃, Max. stirring Capacity 1000mL, suitable for small volume sample precise and stable stirring.

$ 180.00

Electric lifting design is light and convenient, the highest Rotation speed 3000rpm, linear speed of 33m/s, double-end sealing structure to ensure vacuum sealing defoaming, suitable for viscosity ≤ 25000cps materials.

$ 2883.00

Using brushless DC motor to provide 500W output power and 100-1500rpm Speed range, equipped with electric lifting system up to Travel 500mm, with LCD real-time display and 0-9999 minutes timing function, support large capacity low medium and high viscosity material mixing.

$ 3849.00

Driven by serial micro motor, Max. Torque reaches 159.2N.cm, Speed range 0~ 1800rpm stepless speed regulation, suitable for 0~ 50000mPa · s viscosity liquid, compact structure and stable operation.

$ 482.00

Rotation speed up to 3000rpm, line speed up to 33m/s, electric lifting design for easy operation, double-end sealing structure to ensure vacuum sealing defoaming effect, suitable for viscosity ≤ 25000cps material.

$ 3089.00

Cantilever structure to prevent liquid infiltration, large proportion of chilled down surface uniform heat dissipation, Speed range 60~ 2000rpm, Max. Torque 1850gcm, suitable for viscosity of 10000mPa · s liquid stirring.

$ 372.00

Rotation speed up to 3000rpm, maximum linear speed 33m/s, Processing capacity 10-40L, using electric lifting and double-end sealing structure, high dispersion efficiency, vacuum sealing defoaming effect is good, safe and convenient operation.

$ 3151.00

The frequency conversion electromechanical operation is quiet and low noise, the electric lifting operation is convenient, the motor Power is 750W, the spindle Rotation speed is 0-7500rpm, and it is suitable for 0-3L liquid material processing.

$ 993.00

Max. stirring Capacity 1000mL, Speed range 0-1600rpm, using magnetic field drive technology implementation of non-contact stirring, suitable for a variety of low viscosity liquid mixing needs.

$ 107.00

Rotation speed up to 3000rpm, line speed up to 33m/s, Processing capacity 10-40L, using electric lifting and double-end sealing structure, uniform dispersion and vacuum sealing defoaming effect is good.

$ 3089.00

Vacuum sealing defoaming effect, Rotation speed up to 3000rpm, linear speed up to 33m/s, electric lifting operation is convenient, high dispersion efficiency, suitable for viscosity ≤ 25000cps materials.

$ 2986.00

Articles

Lab Mixer Selection - Viscosity Determines Torque
This article mainly discusses how to select a laboratory mixer based on the viscosity of the material. The higher the viscosity, the greater the torque required. Low-viscosity liquids are suitable for high speed and low torque, while high-viscosity materials require low speed and high torque.
Application of Transparent Constant Temperature Water Bath in Visualization of Material Thermal Deformation
The constant temperature water bath provides a stable environment for observing the deformation of materials after heating by maintaining a constant and uniform temperature of the liquid medium.
Improving Efficiency with Vortex Mixers in Biological Sample Pre-treatment
This article primarily discusses how vortex mixers enhance the efficiency of biological sample pretreatment. By generating a vortex motion through an electric motor, they enable rapid and uniform mixing of liquids, saving time and delivering better results compared to traditional manual methods.
Abbe refractometer measures the relationship between refractive index and concentration of liquid coating resins.
This article introduces the method of measuring the refractive index of liquid coating resins using an Abbe refractometer and calculating the concentration based on the relationship between refractive index and concentration.
Negative pressure method leak detector for testing vacuum packaging seal integrity
The negative pressure leak detector evaluates the seal integrity of vacuum packaging by simulating a pressure differential environment. The instrument places the sample in a testing chamber and creates a vacuum to form negative pressure. If there is a leak, air or liquid will seep into the packaging, and the result is determined by observing pressure changes or the presence of bubbles.
The oral dissolving film is uniformly coated by a film applicator and then dried and formed.
Oral dissolving films are prepared by a coating mechanism, where a liquid containing film-forming materials is uniformly applied onto a substrate, followed by drying to remove the solvent and form a solid film.
Abbe refractometer measures the refractive index and concentration of resin liquids.
The Abbe refractometer measures the refractive index of resin liquids using the principle of the critical angle of light, and there is a corresponding relationship between the refractive index and concentration within a certain range.
Surface Tensiometer Evaluates the Wetting and Spreading Properties of Resin Liquids
This article introduces how to use a surface tensiometer to evaluate the wetting and spreading performance of resin liquids. Wetting and spreading affect the adhesion and appearance of products such as coatings and adhesives, and the process can be described by Young's equation and the spreading coefficient.
Key steps for measuring the efflux time of varnish using a viscosity cup method
This article introduces the method for measuring the outflow time of varnish using a viscosity cup. The principle is based on Poiseuille's law, where viscosity is estimated by recording the time it takes for the liquid to completely flow out from the small hole at the bottom of the cup—longer times typically indicate higher viscosity.
Cobb Absorbency Tester Evaluates Paper Water Absorption Capacity
The Cobb water absorption tester is used to measure the water absorption capacity of paper or cardboard by simulating the liquid contact process and calculating the mass of water absorbed per unit area to determine the Cobb value.
Application of Paper Absorbency Tester in Sizing Process
The paper absorbency tester evaluates the absorption performance of paper by measuring the penetration of liquid on the paper. In the sizing process, sizing agents alter the hydrophilicity of the paper fiber surface, thereby affecting the paper's resistance to liquids.
Water Absorption Tester in the Detection of Tissue Paper and Paperboard
This article introduces the application of water absorption testers in the testing of tissue paper and paperboard. The instrument evaluates the water absorption performance of materials by measuring the mass or height of liquid absorbed by the sample, with common methods including the Klemn method and the capillary rise height method.
The flash point tester measures the safety baseline value of the solvent.
The flash point refers to the minimum temperature at which the vapor of a flammable liquid can be ignited. It is not a fixed value but depends on the testing method and instrument. Data measured by flash point testers serve as a critical basis for evaluating the fire risk of solvents and establishing standards for safe storage and operation.
Density Determination: Selection Strategy between Pycnometer Method and Densimeter Method
This article introduces two methods for measuring the density of substances: the pycnometer method and the densimeter method. The pycnometer method calculates density by measuring the mass of a sample of fixed volume. It is suitable for measuring liquids, powders, and small granular solids, offering high precision but slower operation, and requires temperature control.
Surface Tensiometer: Interpreting the Invisible Forces on Liquid Surfaces
Surface tension is the contractile force generated by the uneven forces acting on molecules at the liquid surface, influencing phenomena such as droplet formation and capillarity. Surface tension meters measure this force using techniques like the Wilhelmy plate method, the platinum ring method, or the pendant drop method. Their core components include force sensors, sample stages, and data processing systems.