CATEGORIES

    Standard Tensile Force Gauge

    Overview Products Knowledge Standards Terms
    The standard tensile tester converts force into pointer deflection or digital signals through a spring or sensor, and is used to measure the tensile strength of materials. In quality inspection, it is used to test the tensile resistance of paper, the toughness of plastic films, and the adhesion of inks, ensuring that products meet physical performance requirements.
    Selection
    When selecting, consider that the range should cover the breaking strength of the test object, the accuracy should match the testing standards, the fixtures should be compatible with the material shape, and the calibration certificate should be valid. Environmental temperature effects need to be controlled, metal materials are preferred, and data interfaces should be configured according to recording requirements.
    Display Type
    Principle
    Capacity Range
    Accuracy
    Sensor Connection
    Installation
    Test Function
    Data Output
    Peak Hold

    Terms

    Tensile strength
    Paint Adhesion Tester
    Universal Tensile Tester
    High and Low Temperature Tensile Testing Machine
    Constant Temperature Tensile Testing Machine
    Electronic Tensile Testing Machine
    Single-arm tension testing machine
    Servo Tensile Testing Machine
    Belt Push-Pull Testing Machine
    Pull-off Coating Adhesion Tester

    Standards

    Active GB/T 16825.1-2022
    Metallic materials—Calibration and verification of static uniaxial testing machines—Part1:Tension/compression testing machines—Calibration and verification of the force-measuring system
    Active GB/T 35777-2017
    Mechanical tests for metal alloys adornment chains—Tensile testing
    Active GB/T 8358-2023
    Steel wire ropes—Determination of breaking force
    Active GB/T 18946-2003
    Rubber-coated fabrics--Determination of rubber-to-fabric adhesion--Direct tension method
    Active GB/T 4909.3-2009
    Test methods for bare wires - Part 3: Tensile test
    Active GB/T 17737.316-2018
    Coaxial communication cables—Part 1-316:echanical test methods—Test for maximum pulling force of cable
    Active GB/T 17200-2008
    Technical specification for tensile, compression and flexural testing machines for rubber and plastics (constant rate of rtaverse)
    Active GB/T 16825.2-2018
    Verification of static uniaxial testing machines—Part 2: Tension creep testing machines—Verification of the applied force

    Instruments

    HBO HJJ-12 Fixture Force Gauge Fixture, Max measurement 15000N
    HBO HJJ-12 Fixture Force Gauge Fixture, Max measurement 15000N

    Measured value 15000N, suitable for bolt, screw and other standard parts of tensile strength test, designed for Force Gauge test bench, assist tensile testing.

    $ 186.00
    HBO HJJ-01 Fixture Force Gauge Test Bench Supporting Fixture
    HBO HJJ-01 Fixture Force Gauge Test Bench Supporting Fixture

    Measured value 500N, suitable for rubber, cable, paper, electrical components, Plastic film and other materials tensile force, destructive force, insertion force test, supporting Force Gauge test bench.

    $ 83.00
    HBO HJJ-13 Fixture Force Gauge Fixture, Maximum Measured value 500N
    HBO HJJ-13 Fixture Force Gauge Fixture, Maximum Measured value 500N

    Measured value 500N, suitable for rubber, cable, paper, electrical components, Plastic film and other materials tensile force, destructive force and insertion force test, supporting the Force Gauge test bench.

    $ 86.00
    HBO HJJ-04 Fixture Force Gauge Fixture, Maximum Measured value 500N
    HBO HJJ-04 Fixture Force Gauge Fixture, Maximum Measured value 500N

    Measured value 500N, suitable for fabric, paper, wool, fiber, leather, rubber and other materials tensile force, destructive force and extension test, dedicated to supporting the Force Gauge test bench.

    $ 101.00
    HBO HJJ-06 Fixture Special Fixture for Force Gauge Test Bench
    HBO HJJ-06 Fixture Special Fixture for Force Gauge Test Bench

    Measured value 500N, suitable for all kinds of cable, Glass, leather, electrical components and other materials tensile force, destructive force, insertion force test, designed for Force Gauge test bench.

    $ 89.00
    HBO HJJ-08 Fixture Special Fixture for Force Gauge Test Bench, Maximum Measured value 1000N
    HBO HJJ-08 Fixture Special Fixture for Force Gauge Test Bench, Maximum Measured value 1000N

    Measured value 1000N, suitable for rubber, cable, packing tape, electrical components and other materials tensile force, destructive force, insertion force test, designed for Force Gauge test bench.

    $ 93.00
    HBO HJJ-11 Fixture Special Fixture for Force Gauge Test Bench, Maximum Measured value 5000N
    HBO HJJ-11 Fixture Special Fixture for Force Gauge Test Bench, Maximum Measured value 5000N

    Measured value 5000N, suitable for the tensile strength and destructive force test of steel wire, iron wire, fishing line, nylon wire rope and various cables with a maximum diaMeter of 6mm, specially designed for Force Gauge test bench.

    $ 104.00
    HBO HJJ-17 Fixture Force Gauge Fixture, max measurement 500N
    HBO HJJ-17 Fixture Force Gauge Fixture, max measurement 500N

    Maximum measurement value of 500N, dedicated to supporting the Force Gauge test bench for tensile testing, suitable for clothing button fixing parts strength testing and different button tensile testing.

    $ 194.00
    HBO HJJ-05 Fixture Force Gauge Test Bench Special Fixture Maximum Measured value 500N
    HBO HJJ-05 Fixture Force Gauge Test Bench Special Fixture Maximum Measured value 500N

    Suitable for a variety of material testing, Maximum Measured value 500N, can be matched with Force Gauge test bench for tensile testing, to meet the testing needs of different fields.

    $ 89.00
    HBO HJJ-15 Fixture Force Gauge Fixture, Maximum Measured value 500N
    HBO HJJ-15 Fixture Force Gauge Fixture, Maximum Measured value 500N

    Measured value 500N, suitable for tape, leather, clothing, rubber, electrical components, paper and other materials, assist Force Gauge in tensile testing to ensure test Stability and accuracy.

    $ 143.00
    SUNDOO SJ-030 Meter Mount Clamp, Fixed Force Gauge Display
    SUNDOO SJ-030 Meter Mount Clamp, Fixed Force Gauge Display

    This fixture is specially used to fix the Force Gauge display to ensure that the instrument is stable and does not shake during the test. It is suitable for a variety of Force Gauges to improve Test accuracy and ease of operation.

    $ 138.00
    SUNDOO SPJ-B Hand Press Rack Force Gauge Failure Testing Machine
    SUNDOO SPJ-B Hand Press Rack Force Gauge Failure Testing Machine

    Adopt gear pair drive, hand-pressed operation, rated load 500N, Travel 70mm, the upper and lower height of the frame can be adjusted, Force Gauge has a positioning structure, suitable for batch testing.

    $ 256.00
    LANDTEK FMS-1 Force Gauge measurement bench, push-pull test bench
    LANDTEK FMS-1 Force Gauge measurement bench, push-pull test bench

    It can be used with Force Gauge for vertical and horizontal testing, suitable for accurate measurement of thrust or tension, stable structure and easy operation.

    $ 230.00
    HBO HJJ-09 Fixture Force Gauge Test Bench Special Fixture
    HBO HJJ-09 Fixture Force Gauge Test Bench Special Fixture

    Measured value 500N, suitable for sheet, block material push-pull and destructive force test, can be used with Force Gauge test stand.

    $ 130.00
    HBO HJJ-10 Clamp Force Gauge Maximum Measured value 5000N
    HBO HJJ-10 Clamp Force Gauge Maximum Measured value 5000N

    Measured value up to 5000N, suitable for sheet and block material push-pull force and destructive force test, supporting the Force Gauge test bench.

    $ 78.00

    Articles

    Comparison of Single-Column and Dual-Column Tensile Testing Machines in Plastic Film Testing Selection
    This article introduces the differences between single-column and dual-column tensile testing machines in plastic film testing.
    Application of Small Push-pull Force Gauge in Rapid Inspection of Adhesive Peel Strength for Mobile Phone Screens
    This article introduces how to quickly test the peel strength of adhesive on phone screens using a small push-pull gauge.
    Application of Tensile Testing Machine in 180-Degree Peel Strength Test for Packaging Tape
    This article introduces how a tensile testing machine is used to test the 180-degree peel strength of packaging tape.
    Electronic Tensile Testing Machine Measures the Right-Angle Tear Strength of Films
    This article explains how to measure the right-angle tear strength of films using an electronic tensile testing machine. During the test, a film specimen with a right-angle notch is first clamped onto the testing machine and stretched at a constant speed. The machine records the changes in force during the tearing process.
    Tensile testing machine measures the bending fatigue life of flexible OLED films.
    This article introduces a method for testing the bending fatigue life of flexible OLED films using a tensile testing machine. The test simulates repeated bending to evaluate the accumulation of damage in the film under cyclic stress, and monitors performance changes to determine the failure point.
    Electronic universal testing machine measures film tensile strength.
    This article introduces the method of measuring the tensile strength of thin films using an electronic universal testing machine. During the test, the machine applies tensile force to the film sample, records the maximum tensile force and displacement through sensors, and then calculates the tensile strength using a formula.
    Determination of Static Surface Tension of Color Coatings Using the Platinum Plate Method with a Surface Tensiometer
    This article introduces the method of measuring the static surface tension of colored paints using the platinum plate method. It explains the principle, which involves calculating the surface tension by measuring the force when the platinum plate is lifted from the liquid surface.
    Adhesion Tester Pull-Off Method for Determining Adhesion Strength of Varnish
    This article introduces the test method for measuring the adhesion strength of varnish using the pull-off method. It involves adhering test cylinders to the coating and substrate with adhesive, then vertically pulling them apart with an instrument to record the maximum pulling force and calculate the adhesion strength.
    Electronic tensile testing machine testing the tensile strength of packaging film
    This article introduces the method of testing the tensile strength of packaging films using an electronic tensile testing machine. It first explains the importance of tensile strength for packaging films, then details the testing principles, equipment composition, and the necessity of preparing samples according to standards.
    Method for Determining Peel Strength of Hot Melt Adhesives Using an Electronic Tensile Tester
    This article introduces the standard method for determining the peel strength of hot melt adhesives using an electronic tensile testing machine. The test employs a 180° peel mode, where a sample coated with hot melt adhesive is clamped in the machine's fixtures and peeled at a constant speed. The peel strength is calculated based on the recorded force variations.
    Adhesion tester evaluates the bonding strength between coating and substrate.
    The adhesion tester is a device used to measure the bonding strength between a coating and the substrate. It applies a pulling force until the coating detaches, records the force value, and calculates the strength. Common testing methods include the pull-off method, cross-cut method, etc., each with corresponding standards.
    Pull-off testing for interlayer adhesion of multilayer coating systems.
    This article introduces the pull-off method for testing the interlayer adhesion of multilayer coating systems. The test involves vertically bonding a pull-off head to the coating surface and applying a pulling force until the coating separates, measuring the required force to evaluate adhesion strength.
    Tensile testing machine tests the tensile strength of industrial tape.
    This article explains how to use a tensile testing machine to test the tensile strength of industrial tapes. Tensile strength is a key indicator for measuring the mechanical properties of tapes, and testing must comply with international standards such as ISO and ASTM.
    Tensile Testing Machine Evaluates High and Low Temperature Tensile Properties of Hot Melt Adhesive
    This article introduces how to use a tensile testing machine to test the tensile properties of hot-melt adhesives at different temperatures. The performance of hot-melt adhesives varies with temperature: they may soften at high temperatures and become brittle at low temperatures.
    Tensile testing machine for testing the puncture resistance of film materials.
    This article introduces how to use a tensile testing machine to test the puncture resistance of film materials. Puncture resistance is a key indicator for measuring a film's ability to resist penetration by sharp objects, directly affecting the protective performance of packaging.