Please contact customer service
With retractable bridge design, suitable for sink width not exceeding 885mm, easy installation. Heating power up to 3000W, pump Flow rate is 12L/min, with pressure/suction pump function, support domestic circulation and external circulation applications, and comply with DIN12876 safety standards.
Category : Thermostatic Bath
Brand : labtop
SKU : NB030895
Service :The delivery and service By NBCLab.Com
The immersion thermostatic circulator BHC 30E is a multi-functional heating device that integrates heating, stirring, temperature measurement, temperature control and circulation functions. It features a retractable bridge design and can be easily installed on sinks up to 885mm wide for precise temperature control of samples in the bath. The device can be used in combination with a chill down thermostatic circulator to extend the Temperature range. It is equipped with a powerful pressure and suction pump, DIN12876 Safety level III (FL), allows the use of flammability liquids, and supports external circulation temperature control and connection to a cold water source to chill down.
1. The instrument can be easily installed on different sinks through the retractable bridge. 2. Powerful pressure/suction pump. 3. Good Temperature Control Stability. 4. Safety level III (FL) in accordance with DIN12876 standard, flammability liquids can be used. 5. Convenient domestic circulation and external circulation applications. 6. High and low temperature alarm function. 7. Over-temperature automatic cut-off/anti-dry burning function. 8. Low liquid level alarm function. 9. Adjustment of multiple points. 10. When the alarm is called, the light and sound are reminded at the same time. 11. Adjustable Temperature range, safer to use. 12. Communication interface configurable (RS232/USB).
The device uses an intelligent PID control algorithm combined with a Pt100 temperature sensor for accurate temperature measurement, and controls the 3000W Heating power to heat the bath medium. The built-in pressure/suction pump (Flow rate 12L/min) drives the medium circulation to ensure uniform temperature. The retractable bridge is fixed to the external sink to realize immersion thermostatic control. The device has multiple Safety protection mechanisms, such as over-temperature cutoff, low liquid level alarm, etc., to ensure safe operation.
Laboratory thermostatic control, chemical reaction process temperature control, sample thermostatic treatment, material testing, high and low temperature cycle testing in combination with chilled down equipment
DIN 12876
1. Adjust and fix the retractable bridge according to the width of the sink, and install the instrument on the sink. Make sure that the depth of the bath liquid is not less than 150mm, and connect the power supply (200~ 230VAC/50Hz). 3. Set the target temperature and safety parameters through the device panel. 4. Start the equipment, the pump starts working, and the heating system runs according to the set program. 5. Monitor the temperature display and equipment operation status, and perform data communication or calibrate through optional interfaces (such as RS232/USB) if necessary. 6. After use, turn off the device and disconnect the power according to the procedures.
• When installing, ensure that the width of the sink is within the range of 345mm to 885mm, and the liquid depth is not less than 150mm. • When using flammability liquids, it must be confirmed that the equipment is in compliance with DIN12876 III/FL Safety level. • Note that the Ambient Temperature allowed by the equipment is 5~ 32 ° C, and the relative humidity is ≤ 80%. • During operation, pay attention to lighting and sound alarm prompts. In case of high and low temperature, low liquid level or over-temperature, it should be dealt with in time. • Power supply voltage in the range of 200~ 230VAC, the input Power does not exceed 3100W. • The continuous operation of the equipment is allowed to be 100%, but it must be used under the specified environment conditions. • When calibrating or external communication, please refer to the operating instructions for the relevant optional functions.
[A] No, it isn't. This is the ex-factory price of the product in the Chinese Mainland. In addition to this price, buyers from different countries need to account for additional costs such as shipping fees, tariffs, and others. For specific regional quotes, please consult our customer service or fill out a quotation form.
[A] First, please click on the quotation form on the website and fill in detailed information. Our customer service personnel will then send you a quotation based on your specific country and region, confirming payment and delivery methods. Following this, we proceed with contract signing, payment, and shipment. You can then await delivery.
[A] After-sales repair for overseas instruments is an unavoidable issue. Our repair terms stipulate that the sender is responsible for the shipping and insurance costs incurred for the repair. Repairs within the warranty period are free, while repair costs beyond the warranty period are determined based on the actual situation.
