Overview
Sanenchi YS3060 spectral color difference meter is a China grating Colorimeter independently developed by 3nh company with complete independent intellectual property rights. It adopts full Illuminant, dual-caliber design, supports SCI/SCE measurement, includes UV/exclusion UV measurement function, has USB/Bluetooth 4.0 dual-mode communication, high accuracy and large Storage capacity, suitable for accurate analysis and transmission of laboratory Color. The instrument is stable, accurate measurement Color, powerful, and is in a professional position in the field of Portable Colorimeter. YS multifunctional test components can be used for reflection color measurement of high concentration liquid Reagents, sauces (such as ketchup, Coatings), powders (such as coffee) and other samples.
Features
D/8 geometrical optics, conforming to CIE No. 15, GB/T 3978, GB 2893, GB/T 18833, ISO7724/1, ASTM E1164, DIN5033 Teil7 standards
2. Combination LED Illuminant with High Life and Low Power Consumption, Including UV/UV Exclusion
3. Good combination of beautiful Appearance and structural design in line with human mechanics
4. The diameter of φ 8/4mm can be switched arbitrarily to adapt to more tested samples; at the same time, the measurement of SCI and SCE
5. Light spectrum measurement, Lab data accuracy, can be used for color scheme and accurate Color transfer
6. High electronic hardware configuration: 3.5 inch TFT true color screen, capacitive Touchscreen, concave grating, 256 pixel dual array CMOS detector, etc
7. USB/Bluetooth 2.1 dual communication mode, wider adaptability
8. Super stain-resistant, stable standard whiteboard
9. Large-capacity storage space, capable of storing more than 20,000 test data
10. Two Standard Observer angles, a variety of Illuminant modes, a variety of color systems, chroma indicators that meet a variety of standards, to meet the needs of various customers for Color measurement
11. Camera viewfinder positioning
12. PC-side software has powerful functional extensions
Principle
YS3060 spectroscopic color difference meter adopts D/8 geometrical optics structure, diffuse illumination, 8 ° direction reception, supports SCI/SCE measurement and includes UV/exclude UV measurement. Light spectrum half-Bandwidth 10nm is used to capture Light spectrum data with 256 pixel dual-array CMOS image sensor, and the measurement reflectance range is 0~ 200% to achieve accurate analysis and transmission of Color space.
Applications
Plastic electronics, paints inks, Spinning & weaving garment printing and dyeing, printing paper products, automobiles, cosmetics, food, scientific research institutions, laboratories
Standards
CIE No.15、GB/T 3978、GB 2893、GB/T 18833、ISO7724/1、ASTM E1164、DIN5033 Teil7
Steps
1. YS multifunctional test components should be used in conjunction with YS series Colorimeter. Before use, YS series Colorimeter should be professionally calibrated for black and whiteboard
2. Place the YS series colorimeter as shown in the figure. Among them, the measurement port of the colorimeter should be connected with the measurement port of the bracket. At the same time, the two base baffle pins should be aligned with the baseplate reference hole of the YS colorimeter. Then hold the push plate against the colorimeter, tighten the screws, and check whether the colorimeter is loose. If it is loose, please be sure to tighten the screws again
3. Load the Cuvette loaded with the sample to be tested into the bracket. Gently push away the swirl/spin platen and gently put it into the Cuvette. The Cuvette is pressed against the measurement port of the instrument while being pressed by the swirl/spin platen; note that the liquid height in the Cuvette should be greater than the matching height of the test caliber (that is, the sample height reaches more than half a cup)
4. Cover the cover to ensure that the inside of the Cuvette is an all-black environment. After completing the above steps, you can use the YS series colorimeter to perform reflection chromaticity measurement on the sample
Notice
• Black and white board correction must be performed before use
• When installing the colorimeter, make sure that the measurement port is well connected with the measurement port of the bracket and the reference hole is aligned
• Check whether the colorimeter is loose after tightening the screws. If it is loose, please tighten it again.
• The height of the liquid in the Cuvette should be greater than the matching height of the test caliber, that is, the height of the sample should reach more than half a cup
• Make sure the inside of the Cuvette is an all-black environment before measurement
