Chengyue CY-VPS500-3GN vacuum pyrolysis lame plating machine, multi-layer film prepative equipment

Name: Chengyue CY-VPS500-3GN vacuum pyrolysis lame plating machine, multi-layer film prepative equipment
Brand: ChengYue
SKU: NB045912
Price: 35574.0 USD
Availability: InStock

$ 35574.00Ex works

Equipped with three high voltage gas driven atomization nozzles and anti-drip baffles, support inert gas protection lame plating at 5000Pa basic Vacuum Level, with 0.006-41mL/min precision peristaltic pump and 180mm Travel moving mechanism, to achieve uniform multi-layer film Preparative.

Model

CY -VPS500-3GN

Get Quote

Category : Lab Spray Coater

Brand : ChengYue

SKU : NB045912

Service :The delivery and service By NBCLab.Com

Overview

The CY-VPS500-3GN vacuum pyrolysis lame plating machine adopts the spray pyrolysis Moulding method, and the desired material structure is obtained by spraying the solution atomization onto the heating base. The equipment adds a multi-nozzle coordination system and a vacuum system on the basis of ordinary pyrolysis lame plating. It is equipped with three high voltage gas-driven atomization nozzles and anti-drip baffles. It can work together to produce multi-layer films through touch screen. The vacuum system provides a 5000 Pa basic Vacuum Level to support spray pyrolysis in an inert gas protected environment.

Features

1. Equipped with three high voltage gas driven atomization nozzles and anti-drip baffles 2. The multi-nozzle coordination system can work together through the touch screen 3. Vacuum System Provides 5000Pa Base Vacuum Level 4. Support spray pyrolysis in inert gas protected environment 5. High Accuracy Peristaltic Pump and Precision Programmable Stepper Motor Moving Mechanism 6. substrate temperature can be controlled 7. Maximum temperature up to 500 ° C 8. spray booth size is 690 × 690 × 790mm

Principle

Spray pyrolysis Moulding method is used to spray the solution on the heating substrate after high voltage gas atomization to form the desired material structure on the surface of the substrate. The device works in a vacuum or inert gas protective environment, and accurate thin film preparation is achieved through a multi-nozzle coordination system and a temperature Control system.

Applications

Perovskite solar cell prepative

Steps

1. Prepare the solution and load it into the drip coating tank 2. Set substrate temperature and vacuum environment parameters 3. Coordinate multi-nozzle work through touch screen 4. Start peristaltic pump and moving mechanism for lame plating 5. Finish film prepative on heating substrate

Notice

• Check whether the power supply voltage is AC220V, 50Hz before use • Note that the liquid viscosity range should be within 1-50mPa · s (cP) • Ensure that the vacuum system works properly during operation • Note that the maximum Power of the device is 3.5KW. Keep the working environment well ventilated

supply Voltage
AC 220V, 50Hz
maximum temperature
500℃
Spray booth Size
690*690*790mm
Temperature control mode
Al-PID temperature control
Atomization head
High Voltage air atomization nozzle * 3, each nozzle is equipped with a high Voltage gas drive baffle to prevent dripping
pressure regulator
Adjustable compressed air intake
Maximum Power
3.5Kw (including compressor + peristaltic pump about 1.5Kw)
liquid viscosity
1-50mPa·s(cP)
Nozzle Travel
X-Y axis up to 180mm
traverse speed
X-axis direction: 0-250mm/s, Y-axis direction: 0-250mm/s
Heating substrate substrate Size
200*200mm
Drip coating tank capacity
50mL/250mL/50mL (with one large, two small and three jars)
Peristaltic pump liquid separation rate
0.006-41mL/min
Vacuum pump Type
Two-stage rotary vane vacuum pump
Vacuum Gauge Type
Mechanical vacuum gauge
Ultimate vacuum degree
≤5000Pa
Control method
Industrial control computer + instrument panel
Machine Size
900*900*1750mm

[Q] Is the price listed on the website the final cost for overseas purchases?

[A] No, it isn't. This is the ex-factory price of the product in the Chinese Mainland. In addition to this price, buyers from different countries need to account for additional costs such as shipping fees, tariffs, and others. For specific regional quotes, please consult our customer service or fill out a quotation form.

[Q] What is the specific process for purchasing the product?

[A] First, please click on the quotation form on the website and fill in detailed information. Our customer service personnel will then send you a quotation based on your specific country and region, confirming payment and delivery methods. Following this, we proceed with contract signing, payment, and shipment. You can then await delivery.

[Q] What should I do if the instrument I purchase needs repair?

[A] After-sales repair for overseas instruments is an unavoidable issue. Our repair terms stipulate that the sender is responsible for the shipping and insurance costs incurred for the repair. Repairs within the warranty period are free, while repair costs beyond the warranty period are determined based on the actual situation.