Please contact customer service
The equipment Spreader Film thickness range of 0.005-3mm, Oven temperature up to 200 ℃, using servo drive and PLC control, with automatic tension and correction function, suitable for a variety of coils and Spreader liquid continuous experimental film.
Category : R2R Coater
Brand : Factory
SKU : NB049126
Service :The delivery and service By NBCLab.Com
Rxg-05/1000pro automatic film applicator is a continuous experimental automatic film applicator with the functions of unwinding, scraping, drying and winding. The film width of the machine can reach 1000mm, the adjustment range of wet film thickness is 0.005-3mm, and the oven heating temperature can reach 200 ° C. It is suitable for Spreader experiment and production of various materials such as UV coatings, self-adhesive, plaster, etc.
1. Adopt PLC control and color Touchscreen man-machine interface, easy to operate and use. 2. The main drive is driven by a servo motor, and the speed can be precisely set and adjusted. 3. Equipped with automatic tension control and automatic deviation correction functions to ensure the stability of the belt. 4. Equipped with hot air circulation oven, high temperature control accuracy. 5. Spreader Film thickness can be adjusted manually, regulator resolution up to 0.001mm. 6. The equipment structure adopts aluminum alloy and high electrostatic spray plate, and the transmission platform is made of stainless steel, which has good durability. 7. Equipped with safety protection functions such as emergency stop buttons.
The device adjusts the unwinding tension and the winding tension respectively by controlling the torque of the unwinding shaft and the rewinding shaft, and achieves belt control with the swirl/spin linear speed of the main drive steel roller as a reference. When Spreader, the substrate is unrolled and scraped through an adjustable drawdown blade. Spreader Film thickness is determined by a manually adjusted dial indicator. The substrate after Spreader enters the hot air circulation oven, and the substrate is heated and dried by electric heating air. Finally, the process is completed by Laminating and winding.
Plastic film, metal foil, paper, non-woven fabric and other coils, water-based paints, solvent-based paints, UV coatings and other Spreader liquid coating experiments and production.
The information does not mention the specific standards that the product meets.
1. Install the base material on the inflatable shaft unwinding rack. 2. According to requirements, set the Spreader width through the glue width adjustment device. 3. swirl/spin the left and right handwheels on the rubber roller rack, combined with the dial indicator, adjust to the desired Spreader Film thickness. 4. Manually pull the substrate between the upper and lower rollers of the traction roller, and tighten the handwheel of the rack to make the rubber ring of the upper roller contact with the lower roller. 5. Set coating speed, oven temperature, tension and other parameters through PLC Touchscreen. 6. Start the equipment, the automatic correction device will ensure that the material is aligned, and the equipment will automatically complete the process of scraping, drying, Laminating and winding. 7. After the Spreader is completed, the material is collected through the rewinding inflatable shaft.
• Operating Environment Temperature should be 10 ℃~ 40 ℃, Humidity should be in the range of 30~ 90% RH. • Equipment power requirements are 380V, 50Hz, three-phase five-wire system. • Compressed air of 0.5 to 0.8 MPa is required as a gas source. • The upper load-bearing limit of the winding inflatable shaft is 50KG, please do not overload. • Please pay attention to safety when operating, and use the emergency stop button in case of emergency. • Spreader Film thickness adjustment should refer to the dial indicator to ensure accuracy. • The equipment has large dimensions, and enough space needs to be reserved during installation.
[A] No, it isn't. This is the ex-factory price of the product in the Chinese Mainland. In addition to this price, buyers from different countries need to account for additional costs such as shipping fees, tariffs, and others. For specific regional quotes, please consult our customer service or fill out a quotation form.
[A] First, please click on the quotation form on the website and fill in detailed information. Our customer service personnel will then send you a quotation based on your specific country and region, confirming payment and delivery methods. Following this, we proceed with contract signing, payment, and shipment. You can then await delivery.
[A] After-sales repair for overseas instruments is an unavoidable issue. Our repair terms stipulate that the sender is responsible for the shipping and insurance costs incurred for the repair. Repairs within the warranty period are free, while repair costs beyond the warranty period are determined based on the actual situation.
