Please contact customer service
Continuous experimental film equipment, Spreader width up to 300mm, wet film thickness can be accurately adjusted between 0.005-3mm, drying tunnel temperature up to 200 ℃. PLC control and Touchscreen operation, with automatic tension and deviation correction control, support hot air circulation drying.
Category : R2R Coater
Brand : Factory
SKU : NB049146
Service :The delivery and service By NBCLab.Com
Rxg-03/300cspro drawdown blade Coater is a continuous experimental Automatic Film Applicator with roll, scrape, dry and roll functions. It is specially designed for pharmaceutical patches and other applications. The film width of the machine is 300mm, the wet film thickness range is 0.005-3mm, and the drying tunnel temperature can reach 200 ° C. It is suitable for various Spreader liquids such as UV coatings, stickers, plasters, etc.
1. Adopt PLC control and color Touchscreen (HMI) man-machine interface, easy to operate. 2. The main drive adopts servo drive, the speed can be set, and the coating speed can be adjusted within the range of 1~ 10m/min. 3. Equipped with automatic tension control and automatic deviation correction control to ensure the stability of the belt and accurate material alignment. 4. The oven adopts hot air circulation heating method, and the temperature control accuracy is high (+/- 3 ℃). 5. Spreader accuracy is high (+/- 3%), Film thickness regulator resolution up to 0.001mm. 6. The equipment structure adopts aluminum alloy and high electrostatic spray plate, the transmission platform is stainless steel, and the overroller is Teflon non-stick rubber roller, which is durable and suitable for a variety of materials.
The device adjusts the tension of the substrate by controlling the torque of the releasing and reeling shafts, and uses the swirl/spin linear speed of the main drive roller as the main drive to achieve continuous belt control. When Spreader, the wet film thickness is controlled by adjusting the gap between the drawdown blade and the coating roller (indicated by the percent table). The substrate after Spreader enters the hot air oven, and the substrate is heated and dried by electric heating air, followed by subsequent processes such as roll pressing and hob cutting.
Suitable for Plastic film, metal foil, paper, non-woven fabrics and other coils Spreader water-based paints, solvent-based paints, UV coatings, etc., especially for pharmaceutical patches, plasters, self-adhesive labels and other products of the experiment and production Spreader.
The data did not mention specific compliance criteria.
1. Install the base material on the inflatable shaft unwinding rack. 2. Set the required Spreader width through the gluing width adjustment device. 3. swirl/spin the left and right handwheels on the rubber roller frame, adjust the drawdown blade gap according to the dial indicator, and set the Spreader Film thickness. 4. Set the coating speed, drying temperature and other process parameters on the Touchscreen. 5. Drag the substrate by hand between the upper and lower rollers of the traction roller, and tighten the rack handwheel to make the rubber ring of the upper roller contact with the lower roller. 6. Start the equipment, and the automatic deviation correction and tension control system starts to work, completing the Spreader, Drying, Fitting (if necessary), Slitting (if necessary) and Winding process.
• Operating Environment Temperature should be 10 ℃~ 40 ℃, humidity in the range of 30~ 90% RH. • Compressed air of 0.5 to 0.8 MPa is required as a gas source. • The power requirements are 380V, 50Hz, three-phase five-wire system. • The total power, dimensions and weight of the equipment may vary slightly according to the actual customization, please refer to the final confirmation. • When operating, please ensure that the material type and Spreader liquid type meet the scope of application of the equipment. • Film thickness adjustment, please slowly swirl/spin the handwheel and closely observe the percentage representation to avoid violent adjustment.
[A] No, it isn't. This is the ex-factory price of the product in the Chinese Mainland. In addition to this price, buyers from different countries need to account for additional costs such as shipping fees, tariffs, and others. For specific regional quotes, please consult our customer service or fill out a quotation form.
[A] First, please click on the quotation form on the website and fill in detailed information. Our customer service personnel will then send you a quotation based on your specific country and region, confirming payment and delivery methods. Following this, we proceed with contract signing, payment, and shipment. You can then await delivery.
[A] After-sales repair for overseas instruments is an unavoidable issue. Our repair terms stipulate that the sender is responsible for the shipping and insurance costs incurred for the repair. Repairs within the warranty period are free, while repair costs beyond the warranty period are determined based on the actual situation.
