Please contact customer service
The effective width is 500mm, the drying temperature can be adjusted from room temperature to 100 ° C, and the coating speed is controllable from 0-20m/min. It adopts the integrated design of dip coating and drying, with automatic tension and deviation correction control, and is suitable for a variety of coils and coatings.
Category : R2R Coater
Brand : Factory
SKU : NB049487
Service :The delivery and service By NBCLab.Com
Rgdc-01/500 immersion coil Coater (with drying) is a factory direct sales product with an effective Spreader width of 500mm. It is specially designed for Plastic film, paper, non-woven fabrics and other coils. It can perform dip coating operations on water-based paints, solar-based paints, UV coatings, etc., and complete the drying process synchronously. It is suitable for Spreader needs in a variety of industrial production scenarios.
1. Efficient process: The integrated process of "unwinding → soaking → double roll extrusion residue → drying → Laminating → winding" is adopted, and the production is continuous and efficient. 2. Precise regulation: drying tunnel temperature adjustable room temperature -100 ℃, coating speed 0-20m/min controllable, double roller extrusion gap 1-10mm adjustable (handwheel adjustment with dial meter display), tension and correction automatic control, correction accuracy up to +/- 1mm. 3. Widely applicable: supports a variety of coils and Spreader liquids, and the soaking bath is made of corrosion-resistant stainless steel, which is suitable for different solution characteristics. 4. Stable and reliable: scientific structural design, reasonable winding and unwinding diameter and load-bearing, gas source and power supply adapt to conventional requirements to ensure stable operation of equipment.
The device uses a dip coating process. After the coil is drawn out from the unwinding end, it is immersed in a corrosion-resistant stainless steel bath filled with Spreader liquid to complete the Spreader. Subsequently, the material after the Spreader is passed through a pair of double rollers with adjustable gaps to squeeze to remove excess paint. Next, the material is entered into a drying tunnel with adjustable temperature for drying. After drying, Laminating can be selected, and finally the winding device completes the winding. The whole process is continuously carried out under the control of an automatic tension and deviation correction system.
Suitable for Plastic film, paper, non-woven fabric and other coil Spreader processing, can handle water-based paints, solvent-based paints, UV coatings and other Spreader liquid.
1. Preparation: Confirm that the power supply (single-phase AC220V +/- 10%, 50Hz) and the air source (0.5~ 0.8MPa compressed air) are normally supplied, and install the Spreader coil and Spreader liquid. 2. Parameter setting: According to the process requirements, adjust the double roller extrusion gap (1-10mm, dial meter display) through the handwheel, set the drying tunnel temperature (room temperature -100 ℃) and coating speed (0-20m/min). 3. Wear material: Wear the coil according to the path of "unwinding → soaking → double roller extrusion → drying → Laminating → winding". 4. Start: Open the equipment, the automatic tension and correction system starts to work, and carry out dip coating, extrusion, drying, Laminating and winding operations. 5. Monitoring and winding: Monitor the Spreader and drying process. After the Spreader is completed, the equipment will automatically wind up, with a maximum winding diameter of 200mm and a load-bearing capacity of 50KG.
• The soaking bath is made of corrosion-resistant stainless steel, and the Spreader liquid used cannot chemically react with this material. • Equipment dimensions and weight are subject to actual customization, and sufficient space should be reserved during installation. • Power frequency and gas source pressure must be within the specified range during operation (power supply: single-phase AC220V +/- 10%, 50Hz, power 9.5KW; gas source: 0.5~ 0.8MPa). • Pay attention to safe operation and avoid improper intervention during equipment operation. • Maintain the equipment regularly to ensure that all components (such as guide rollers, extrusion rollers, drying tunnels, etc.) operate normally.
[A] No, it isn't. This is the ex-factory price of the product in the Chinese Mainland. In addition to this price, buyers from different countries need to account for additional costs such as shipping fees, tariffs, and others. For specific regional quotes, please consult our customer service or fill out a quotation form.
[A] First, please click on the quotation form on the website and fill in detailed information. Our customer service personnel will then send you a quotation based on your specific country and region, confirming payment and delivery methods. Following this, we proceed with contract signing, payment, and shipment. You can then await delivery.
[A] After-sales repair for overseas instruments is an unavoidable issue. Our repair terms stipulate that the sender is responsible for the shipping and insurance costs incurred for the repair. Repairs within the warranty period are free, while repair costs beyond the warranty period are determined based on the actual situation.
