Please contact customer service
The equipment has a wide range of wet film thickness adjustment, up to 0.005-3mm, and the adjustment resolution is fine to 0.001mm. It adopts servo drive and PLC control to realize automatic constant tension control, stable belt walking, and is equipped with hot air circulation oven for drying.
Category : R2R Coater
Brand : Factory
SKU : NB050617
Service :The delivery and service By NBCLab.Com
Rdh-02/350dcblpro coil drawdown blade Coater is a factory direct sales of continuous experimental film equipment. It integrates unwinding, scraping, soaking, disbonding, drying, winding functions, wet film thickness range of 0.005-3mm, suitable for hot-melt adhesive, sticker, plaster and other materials Spreader experiment and production.
1. With continuous Spreader function, integrated scraping, soaking, disbonding, drying and other processes. 2. Adopt PLC control and color Touchscreen (HMI) operation, easy to use. 3. The main drive adopts a servo motor, and the speed can be precisely set. 4. Equipped with a fully automatic constant tension control system and an automatic deviation correction device to ensure the stability of the belt. 5. Adopt hot air circulation oven, temperature controllable. 6. Spreader Film thickness can be adjusted manually, and equipped with digital dial meter, resolution up to 0.001mm. 7. Equipment is equipped with an emergency stop button, providing safety protection.
The device adjusts the tension of the substrate by controlling the torque of the release and reel, and uses the swirl/spin linear speed of the main drive roller as the main drive speed to control the belt. When Spreader, the substrate passes through the adjustable Blade Coating head, and the wet film thickness is controlled by adjusting the handwheel and the dial meter. Subsequently, the substrate can enter the soaking section for soaking treatment, then go through the disbonding section, and finally enter the hot air oven for drying. The oven uses electric heating air to heat the substrate.
Encasement, electronics, construction, automotive, medical, etc
1. Install the base material on the inflatable shaft unwinding rack. 2. Set coating speed, tension, drying temperature and other parameters through Touchscreen. 3. According to the required Film thickness, swirl/spin coating roller rack left and right handwheels, refer to the dial indicator to adjust the drawdown blade clearance. 4. Manually pull the substrate between the upper and lower rollers of the traction roller, and tighten the handwheel of the rack to make the rubber ring of the upper roller contact with the lower roller. 5. Start the equipment, the automatic correction device will ensure that the material is aligned, and the traction roller group will pull the substrate to complete the Spreader, soaking, disbonding, and drying process. 6. Spreader drying material by the inflatable shaft rewinding rack for rewinding.
• Before use, please confirm that the Power frequency is 380V, 50Hz, three-phase five-wire system, and the gas source pressure is 0.5~ 0.8MPa. • Operating Ambient Temperature recommended at 10 ℃~ 40 ℃, humidity in the range of 30~ 90% RH. • Spreader fluid types must be compatible with equipment, such as water-based paints, solar-based paints, UV coatings, etc. • The maximum roll diameter of discharging and receiving is φ 350mm, and the winding bearing capacity does not exceed 50KG. • When adjusting Spreader Film thickness, slowly swirl/spin the handwheel and carefully observe the dial indicator. • In case of emergency during equipment operation, please press the emergency stop button immediately. • The total power and dimensions of the equipment may be slightly different due to customization, please refer to the actual situation.
[A] No, it isn't. This is the ex-factory price of the product in the Chinese Mainland. In addition to this price, buyers from different countries need to account for additional costs such as shipping fees, tariffs, and others. For specific regional quotes, please consult our customer service or fill out a quotation form.
[A] First, please click on the quotation form on the website and fill in detailed information. Our customer service personnel will then send you a quotation based on your specific country and region, confirming payment and delivery methods. Following this, we proceed with contract signing, payment, and shipment. You can then await delivery.
[A] After-sales repair for overseas instruments is an unavoidable issue. Our repair terms stipulate that the sender is responsible for the shipping and insurance costs incurred for the repair. Repairs within the warranty period are free, while repair costs beyond the warranty period are determined based on the actual situation.
