Mineral Slurry RheoMeter

The slurry rheometer determines parameters such as viscosity and yield stress by measuring the flow characteristics of slurry under shear forces. It is used to evaluate the transport and processing behavior of slurry, aiding in the control of slurry density and stability during mining and mineral processing operations.

Instruments

Illuminant lighting luminance adjustable, equipped with swing Abbe condenser numerical aperture 1.30, provide plaster lambda and quartz wedge compensator, support 360 degree swirl/spin table.

$ 2034.00

Contains 1026 standard Colors, conforming to the National Standard for Architectural Color Representation Methods, displaying 6 color samples per page, suitable for architectural color selection and management.

$ 130.00

The dust density is measured by natural accumulation method, the diaMeter of the outflow port is 12.7mm, the funnel taper is 60 ° +/- 0.5 °, to ensure the stability of the free fall process, the volume of the measuringflask is 100mL, and the material is durable and easy to clean.

$ 235.00

Using parallel illumination hemispherical scattering integrating sphere photoelectric receiving mode, the accuracy of light transmitance and haze display is 0.01%, equipped with thin film magnetic fixture and liquid sample Cup, and supports 2000 sets of data storage.

$ 3882.00

Made of stainless steel, the slurry diaMeter is 50mm, the Rod length is 400mm, the mixing performance is mild, the tangential flow is generated during medium and low speed operation, the turbulence is small and the heat exchange effect is good.

$ 96.00

Equipped with 7-inch Touchscreen, easy to operate, support stepless speed measurement and viscosity automatic conversion, measurement range 1~ 75000000mPa.s, gigabit network port to ensure fast and reliable data transmission.

$ 3244.00

Driven by stepper motor, folding speed 10-200cpm, adjustable test angle 10-180 °, with automatic counting and disconnection automatic stop function to ensure Test accuracy.

$ 1776.00

High sampling accuracy, parallelism ≤ 0.015mm, thickness range of 0.1~ 1.2mm, suitable for a variety of paper strength tests to ensure accurate and reliable detection data.

$ 687.00

The shear rate is 5.0N, the sample volume is only 170μL, the applicable viscosity range is 50~ 100000mPa · s, suitable for a variety of fluid measurement, high measurement accuracy.

$ 683.00

Made of stainless steel, the diaMeter of the slurry is 50mm, the Rod length is 350mm, and the medium and high speed stirring performance is stable, which is suitable for mixing operations of various medium and low viscosity liquids.

$ 99.00

Made of stainless steel, the diaMeter of the slurry is 50mm, the Rod length is 300mm, and the stirring performance is mild, which is suitable for medium and low speed working conditions and can achieve a soft stirring effect.

$ 91.00

The stirring performance is mild and suitable for medium and low speed use, the slurry diaMeter is 100mm and the Rod length is 500mm, and the tangential flow turbulence is small and the heat exchange performance is good.

$ 112.00

The device places the test plate in parallel in the wind tunnel, the wind speed control accuracy is 3 +/- 0.3m/s, the drying time is automatically controlled, and the surface crazing can be visually inspected, which is suitable for the evaluation of coating anti-crack performance.

$ 490.00

Equipped with 7-inch Touchscreen operation interface, supports high-speed data transmission of gigabit network port, measurement accuracy of +/- 2%, temperature control accuracy +/- 0.1 ℃, with automatic lifting and anti-static design.

$ 11125.00

Adopt natural convection cycle to avoid sample volatilization, stainless steel liner is easy to clean, temperature control accuracy of +/- 0.5 ℃, optional multi-stage programming and independent temperature limit alarm system.

$ 419.00

Articles

Rotational rheometer measures the viscosity and processing performance of polymer melts.
A rotational rheometer applies a controlled shear field to measure rheological parameters such as the viscosity of polymer melts. The melt typically exhibits shear-thinning behavior, where its viscosity changes with the shear rate, directly affecting processing methods such as extrusion and injection molding.
Melt Flow Indexer and Torque Rheometer in the Evaluation of Processing Properties of Thermoplastic Resins
This article introduces the differences and selection methods between melt indexers and torque rheometers in evaluating the processing properties of thermoplastic resins.
Comparison of Rotational Viscometer and Capillary Rheometer in Testing the Flowability of Resin Processing
The rotational viscometer measures torque via rotor rotation, making it suitable for testing the static or low-shear fluidity of resins under low shear rates, with simple and quick operation. The capillary rheometer, on the other hand, forces samples through a capillary to simulate high-shear processing, providing flow data closer to actual production conditions, but it is more complex and time-consuming to operate.
Rheometer combined with UV light source to study the curing behavior of photopolymerizable resin
This article introduces how to combine a rheometer with a UV light source to study the curing process of UV-curable resins.
Capillary Rheometer for Determining the Shear Viscosity Curve of Hot Melt Adhesives
This article introduces the method of measuring the shear viscosity curve of hot melt adhesives using a capillary rheometer. The principle involves pushing molten hot melt adhesive through a capillary, measuring the pressure and flow rate, and then calculating the shear stress and viscosity.
Can you distinguish between a rotational viscometer, a rheometer, and a cone-plate viscometer?
Rotational viscometers, rheometers, and cone-plate viscometers are core instruments in the field of material characterization, with significant differences in measurement principles, geometric structures, and functional positioning.