Free Fall Tester

The free fall test machine simulates the accidental drop of products during transportation or use. It uses a release device to allow the sample to fall freely from a set height and impact a rigid plane, thereby testing its impact resistance and structural integrity. It is used for quality verification in industries such as packaging materials, electronic devices, and toys.
Selection
When selecting a free fall testing machine, it is essential to consider the compatibility of the drop height range with the testing standards, ensure the size of the loading platform accommodates the sample specifications, verify that the drop method meets the testing requirements, guarantee control accuracy for reliable results, confirm the durability of the equipment material, ensure comprehensive safety protection devices, and prioritize a simple and user-friendly operation interface.

Terms

Standards

Instruments

Impact performance of the reflective film can be accurately measured by using the principle of free fall of steel ball, steel ball mass 450 +/- 3g, drop 250mm, reasonable structure and simple operation, safe and reliable measurement.

$ 582.00

With 1000g drop weight and 8mm punch, Impact height can be adjusted to 100cm, the degree of film damage is tested by free fall, and the structure is stable and easy to operate.

$ 264.00

The pure oil-free design ensures that the gas is clean and pollution-free, the exhaust volume reaches 608L/min to meet the high-efficiency gas supply demand, the noise control is about 45 decibels to achieve ultra-quiet operation, the automatic operation does not require special personnel to be on duty, and the optional dew point of the dryer is supported as low as -60.

$ 2550.00

Pure oil-free design, displacement 116L/min, exhaust pressure 8bar, automatic start and stop, low energy consumption, high gas cleanliness, simple operation and convenient maintenance.

$ 353.00

Using electromagnetic motor and diaphragm sealing Chamber, Vacuum Level up to 0.08Mpa, pumping rate 60L/min, non-oil pump design pollution-free, full Teflon material resistant to strong acid and alkali corrosion, free of daily maintenance.

$ 388.00

Noise is as low as 54 decibels at work, displacement is 155 liters per minute, pure oil-free piston system ensures clean gas, Nano coating cylinder liner enhances durability, automatic start-stop saves energy and saves electricity.

$ 832.00

The pure oil-free design ensures that the gas is clean, the noise is only 53 decibels, the exhaust volume is 230L/min, the automatic start-stop energy saving and worry-free, and the anti-rust and anti-bacterial treatment of the gas storage Tank ensures safety.

$ 1013.00

With oil-free lubrication piston system, noise is as low as 52 dB, exhaust volume is 118 L/min, automatic start and stop and multiple Safety protection, cylinder liner application Nano coating technology to extend service life.

$ 880.00

The pure oil-free design ensures that the gas is clean, the noise is as low as 42 decibels, the exhaust volume is 116L/min to meet a variety of needs, and the automated operation does not require special personnel to be on duty, making it safe and reliable.

$ 741.00

Noise as low as 52 dB, pure oil-free design ensures zero gas pollution, equipped with 60L buffer Tank and electronic start-stop controller, providing stable air pressure output, suitable for a variety of industrial environments.

$ 961.00

Noise is as low as 52 dB during operation, oil-free lubrication piston system and Nano coating cylinder liner are used, and the exhaust volume reaches 236L/min. Automatic start-stop design reduces energy consumption, and supports Filter selection to improve gas cleanliness.

$ 1526.00

Equipped with 300g to 1000g heavy hammer and five kinds of punch die base, it can adjust the drop height of 50-500mm to meet the needs of anti-impact performance testing of various materials.

$ 848.00

Pure oil-free design ensures clean gas, low noise to 42dB, exhaust pressure 5-8bar, automatic start and stop, low energy consumption, simple operation, no need for special personnel on duty, and can be adapted to a variety of industry needs.

$ 1340.00

Adopting pure oil-free technology, the output gas is clean and oil-free; equipped with a 30L gas storage Tank and 750W Power, the noise is as low as 59dB; with automatic pressure control and overload protection, the service life exceeds 15,000 hours.

$ 687.00

Adopting a pure oil-free lubrication piston system, equipped with a 60L anti-rust and antibacterial gas storage Tank, with an exhaust capacity of 304L/min and a noise of only 60dB. It has multiple automatic protection functions and is easy to operate without the need for a special person to be on duty.

$ 1251.00

Articles

Application of Drop Hammer Impact Testing Machine in Evaluating Impact Resistance of Composite Materials
This article introduces how the drop-weight impact testing machine evaluates the impact resistance of composite materials. The test releases a weight to strike the specimen, measuring parameters such as energy absorption, peak load, and damage area, simulating low-velocity impacts like tool drops.
Dart impact tester measures the toughness of packaging film.
The dart impact test evaluates the material's resistance to damage under dynamic impact, i.e., its toughness, by allowing a dart to fall freely and strike the packaging film. During the test, different impact energies are simulated by adjusting the weight of the dart or the drop height, and sensors are used to detect whether the film ruptures.
Standard Operating Procedure for Packaging Drop Tester
The packaging drop tester is used to evaluate the impact resistance of transport packages during vertical drops. Before operation, it is necessary to check the safety of the equipment, calibrate the drop height, and prepare the test specimens according to standards.
Standards and Equipment Selection for Drop Testing in Mobile Phone Whole-Machine Reliability Testing
Drop test is an important method to test the durability of mobile phones, simulating accidental drops in daily life to examine the impact resistance of components such as the casing and screen. The test must follow international or industry standards, specifying conditions such as drop height and number of times.
The Complementary Relationship Between Drop Testing and Impact Testing in Product Structural Strength Verification
This article discusses the different roles and complementary relationship between drop tests and impact tests in verifying product strength.
Analyzing Packaging Design Defects through Drop Tester Selection
This article discusses how the selection of a drop tester during the packaging design process can actually reveal many design issues early on. For example, determining parameters such as drop height, testing standards, and equipment dimensions during the selection process inherently tests the reasonableness of the design.
When selecting a drop testing machine, whether to choose a single-arm or double-arm configuration depends on the size and weight of the packaging.
When selecting a drop tester, the choice between a single-arm or double-arm model mainly depends on the size and weight of the packaging. For small, lightweight, and regularly shaped items, a single-arm tester is sufficient. However, for larger, heavier, or irregularly shaped items, it is better to choose a double-arm tester, as it offers greater stability and ensures more accurate test results.
Contact Angle Meter Selection Guide: How Can Laboratory Beginners Avoid Pitfalls?
The contact angle measuring instrument is used to analyze the wettability of solid surfaces and has applications in various fields such as materials and coatings. When selecting a model as a beginner, it is necessary to first understand key parameters such as static and dynamic contact angles and surface free energy, and then choose the configuration based on the specific application scenario.