Paint film color matching light box

The paint film color matching light box eliminates ambient light interference by simulating standard light sources such as daylight and fluorescent lamps to illuminate samples, allowing observers to compare color differences under uniform conditions. It is used for production quality inspection and color management in industries such as coatings and plastics.
Selection
When selecting, confirm that the light box is configured with commonly used standard light sources such as D65 and TL84. The inner walls should be neutral gray and matte. The lifespan and light decay data of the light tubes must be clearly specified, and the device should feature automatic switching between light sources. The observation area dimensions should accommodate common sample sizes, and regular calibration of light source stability using standard color tiles is required.

Terms

Standards

Instruments

Provide adjustable illuminance and Color temperature visible light, Color temperature range 2300K-8000K, illuminance up to 3000LX, infrared wavelength 850nm optional, radiation intensity greater than 400uW/CM ², stable light color without stroboscopic, life over 10,000 hours.

$ 5850.00

With a standard 45 degree tilt angle, the same as the light box base color does not interfere with the viewing effect, Dimension 395 * 350mm, weight 1.2Kg, flexible placement and easy to disassemble and transport.

$ 106.00

In line with the LOVIBOND color scale standard, the sub-field of view Color matching Sensitivity is high, the Measurement range is red 0.1-79, yellow 0.1-79 LOVIBOND units, and the structure is simple and easy to operate.

$ 599.00

Transmission surface uniformity of more than 93%, Color temperature adjustment range 2300K-8000K, Illuminance adjustable 0-160,000 Lux, Support Frequency adjustment 1-100KHz, life of more than 10,000 hours, can be connected through RS485 or WIFI computer control.

$ 5366.00

Color temperature adjustment range 2300K-8000K, illumination adjustment range 0-4000Lux, built-in mobile slide can move the camera front and rear, light source light board can swirl/spin to adjust the angle, provide a uniform lighting environment.

$ 5366.00

Using high-power LED Illuminant, Color temperature adjustment range 2300K-8500K, illumination up to 3000LX, life more than 10,000 hours, uniform irradiation surface and no stroboscopic, flexible adjustment of light box position and angle according to test requirements.

$ 12305.00

Equipment provides a variety of standard illuminant options, maximum support three Illuminant, high CRI = 98, with Illuminant Timer, uniform lighting, easy to operate, suitable for Color Comparison.

$ 848.00

With three light source system, color rendering index up to 98, all metal structure with three drawer, table size 1350 * 900mm, in line with ISO3664 international standards.

$ 2365.00

Imported matte aluminum reflector to achieve uniform lighting, equipped with six kinds of Illuminants including D65 and UV, table size 700 * 530mm to meet a variety of color requirements.

$ 687.00

The paint film adhesion was measured by the circular trace method, the drawing diaMeter was 0~ 10.5mm, and the Working Travel was 80mm. The integrity of the paint film was evaluated according to seven grades, and the operation was simple and reliable.

$ 267.00

The uniformity of the transmission surface exceeds 90%, the standard four-speed Color temperature is adjustable, the illuminance adjustment range is 0-120000Lux, and the thickness dimming knob is equipped to achieve precise control. Illuminant has no stroboscopic and the lifespan is more than 10,000 hours.

$ 5237.00

The drying process of paint film and putty film can be accurately measured by using circular track needle design, equipped with four different radius needle (R0.25/0.5/1.0/1 mm), and the track period is 24h/r.

$ 223.00

With CRI = 98 high color rendering index and 6500K color temperature, lamp with Timer, all-metal structure, large folio size for easy operation, can be hung and installed to ensure accurate Color comparison.

$ 719.00

Equipped with five Illuminants including D65 and UV, can activate multiple Illuminants simultaneously, built-in lamp Timer, ISO 3664 and ASTM D1729 compliant.

$ 4857.00

Adopt high-power high-illumination LED Illuminant, Color temperature adjustment range 2300K-8500K, illuminance adjustment range 0-3000LX, no stroboscopic design life of more than 10,000 hours, uniform illumination surface can flexibly adjust the position angle.

$ 5366.00

Articles

Pencil hardness tester rapidly evaluates scratch resistance of paint film.
This article introduces how to quickly assess the scratch resistance of paint films using a pencil hardness tester. During the test, standard pencils (ranging from 6B to 9H) are used to scratch the coating at a fixed angle and pressure to observe whether scratches occur.
Selection Recommendations for Paint Film Cross-Cut Testers Based on Different Adhesion Testing Requirements
This article mainly discusses how to choose the appropriate paint film cross-cut tester based on different adhesion testing requirements.
Evaluation of Coating Adhesion Grade by Cross-Cut Tester Combined with Tape Method
This article introduces the method of evaluating coating adhesion using a paint film cross-cut tester combined with the tape method.
T-bend tester for coatings is used to determine the T-bend grade of metal sheet coatings.
This article introduces how the T-bend tester for paint films is used to evaluate the flexibility and adhesion of coatings on metal sheet surfaces.
Cone Mandrel Bend Tester evaluates the flexibility of coatings under small-diameter bending.
The paint film conical bending tester simulates a gradually varying radius of curvature using a conical shaft to test the flexibility of coatings under small-diameter bending.
Coating Cylindrical Bending Tester for Determining the Resistance of Paint Films to Cylindrical Bending Cracking
This article introduces how the coating cylindrical bending tester measures the resistance of paint films to bending and cracking.
Selection of impact head diameter and drop hammer mass combination for paint film impact tester
When selecting the impactor diameter and drop hammer mass for a paint film impact tester, the key is to balance the impact energy and pressure.
Pencil Hardness Plan Outstanding Paint Film Pencil Hardness Grade
The pencil hardness test is a method for evaluating the scratch resistance of paint films. It involves using a series of pencils with known hardness levels to scratch the coated surface under fixed conditions. The hardness grade of the coating is determined by observing whether permanent scratches are produced.
Cylindrical Mandrel Bending Tester for Detecting Flexibility of Coatings
This article introduces how the cylindrical shaft bending tester detects the flexibility of paints. Flexibility refers to the ability of the paint film to resist cracking when the substrate is bent.
Comparison of the Three Principles of Paint Film Adhesion Testers
There are primarily three principles for paint film adhesion testers, and selection should be comprehensively considered based on the coating characteristics, substrate type, and testing purpose.
Usage of Paint Film Solvent Rub Tester in Rapid Detection of Curing Degree
The paint film solvent resistance tester rapidly evaluates the degree of paint film curing by simulating solvent wiping. Its principle is that a fully cured paint film has a high cross-linking density, enabling it to resist solvent dissolution.
Application of Film Pencil Hardness Tester in Coating Scratch Resistance Testing
The paint film pencil hardness tester is an instrument used to evaluate the scratch resistance of coatings. It works by scratching the surface of the coating with a pencil of known hardness under a fixed load, and then assessing the hardness grade based on whether scratches are produced.
Use of pendulum hardness tester for paint film curing degree assessment in the laboratory.
The pendulum hardness tester evaluates the hardness of a paint film by measuring the decay time of a pendulum swinging on the surface of the film, where a longer time indicates a harder film and a higher degree of curing.
Testing principle of the mandrel bending method for paint film flexibility tester
The shaft-rod bending method is a common technique for testing the flexibility of paint films. It involves bending a test panel coated with the paint film over shafts of different diameters to simulate the deformation of the coating under stress.
Preparation of Paint Film Test Panels
The standardized preparation of paint film test panels is fundamental for accurately assessing the performance of paint films. The entire process includes key steps such as substrate selection and pretreatment, paint preparation, coating, drying and curing, thickness measurement, and curing.