Explosion-proof high and low temperature humidity test chamber

The explosion-proof high and low temperature humidity test chamber simulates high temperature, low temperature, and humid environments within a sealed chamber through heating and cooling systems as well as humidification and dehumidification devices. It is used to test the performance stability and explosion-proof safety of flammable materials such as coatings and inks under varying temperature and humidity conditions. This equipment is widely applied in environmental adaptability testing for products in industries such as chemicals and electronics.
Selection
When selecting an explosion-proof high-low temperature humidity test chamber, it is essential to confirm that the ignition characteristics of the tested materials match the explosion-proof rating of the chamber. Verify that the temperature range covers the commonly used interval of -70℃ to 180℃, with humidity control accuracy within ±2% RH. Pay attention to the corrosion-resistant material of the chamber, and ensure that the explosion-proof structure includes pressure relief devices and intrinsically safe circuits, complying with explosion-proof certification standards such as ATEX or IECEx.

Terms

Standards

Instruments

Using explosion-proof composite explosion-proof technology, pumping rate of 4L/S, noise only 63dB, equipped with gas ballast valve can remove a small amount of water vapor, safe and reliable for dangerous environment.

$ 701.00

Using explosion-proof composite explosion-proof technology, pumping rate 2L/S, noise as low as 63dB, equipped with gas ballast valve can extract a small amount of water vapor, safe and reliable.

$ 517.00

Using explosion-proof composite explosion-proof technology, pumping rate 8L/S, noise as low as 66dB, equipped with gas ballast valve can extract a small amount of water vapor, suitable for flammable and explosive dangerous places.

$ 1024.00

The explosion-proof composite explosion-proof technology is used to ensure safe operation, with anti-suction valve and gas ballast valve, the pumping rate is 48m ³/h, and the ultimate pressure is as low as 0.005mbar, which is suitable for dangerous environments.

$ 1889.00

Using flameproof composite explosion-proof technology, the pumping rate is 1L/S, the ultimate pressure can reach 0.006mbar, and the noise is as low as 63dB, which is suitable for flammable and explosive environments.

$ 462.00

Using explosion-proof composite explosion-proof technology, explosion-proof mark ExdIBT4, pumping rate 90m ³/h, limit pressure as low as 0.005mbar, noise only 58dB, suitable for hazardous environments.

$ 2922.00

Adopt compound explosion-proof technology, pumping rate 0.5L/S, noise value 62dB, equipped with gas ballast valve can extract a small amount of water vapor, safe and reliable to adapt to harsh environment.

$ 462.00

Adopting explosion-proof, burn-seal, intrinsically safe composite explosion-proof technology, with anti-suction valve and gas ballast valve, the pumping rate is 16m ³/h, the ultimate pressure is 0.005mbar, and the noise value is 58dB (A).

$ 1063.00

The use of explosion-proof composite explosion-proof technology to ensure safe operation, pumping rate of 15L/S and noise only 66dB, equipped with gas ballast valve can handle a small amount of water vapor, compact suitable for use in hazardous environments.

$ 1308.00

It adopts explosion-proof composite explosion-proof technology to ensure safe operation. It is equipped with an anti-suction valve to prevent oil from being sucked back. It is equipped with a gas ballast valve to adjust the Vacuum Level. The pumping rate is 24m ³/h, and the noise value is 58dB.

$ 1192.00

Intrinsically safe explosion-proof design, up to CT4 grade, equipped with explosion-proof Sensor and display. Table size 410x510mm, weighing range 110kg, accuracy 10g, stable structure, support external calibrating and a variety of functions.

$ 190.00

Suitable for flammable and explosive environment, explosion-proof grade ExdIBT4, pumping rate 8m ³/h, limit pressure as low as 0.005mbar, equipped with anti-suction valve and gas ballast valve to ensure safe and reliable operation.

$ 882.00

Adopt flameproof composite explosion-proof technology to ensure safe operation, with anti-suction valve and gas ballast valve, pumping rate up to 60m ³/h, limit pressure as low as 0.005mbar, to adapt to a variety of vacuum requirements.

$ 2095.00

Adopt flameproof composite explosion-proof technology to ensure safe operation, with a pumping rate of 6L/S and a noise of only 64dB. Equipped with a gas ballast valve to handle a small amount of water vapor, it is compact and easy to install and maintain.

$ 817.00

Adopt flameproof composite explosion-proof technology to ensure safe operation, equipped with anti-suction valve to prevent oil backflow, pumping rate up to 4m ³/h, limit pressure as low as 0.005mbar, suitable for dangerous environment.

$ 817.00

Articles

Rapid temperature change high and low temperature test chamber for thermal fatigue evaluation of PCB board solder joints.
This paper discusses the application of rapid temperature change high and low temperature test chambers in evaluating the thermal fatigue of PCB board solder joints. Solder joint fatigue is primarily caused by differences in material thermal expansion, and the test chamber simulates thermal stress through temperature cycling to accelerate the fatigue process.
Application of Three-Chamber High and Low Temperature Test Chambers in Rapid Temperature Cycling for Electronic Products
The three-chamber high-low temperature test chamber is used for reliability testing of electronic products, enabling rapid temperature transitions through independent high temperature, low temperature, and test zones. Compared to traditional single-chamber equipment, it reduces temperature change time and enhances testing efficiency.
High and low temperature alternating test chamber for measuring low-temperature embrittlement temperature of plastics
This article introduces how to use a high-low temperature alternating test chamber to determine the low-temperature brittleness temperature of plastics.
Thermal Shock Test Chamber Measures Film's Temperature Change Resistance
The thermal shock test chamber creates thermal stress inside the film by rapidly switching between high and low temperature environments, testing its resistance to temperature changes. During the test, key parameters such as temperature range and dwell time need to be set, and the film is observed for issues such as cracking or performance degradation.
Humidity and heat test chamber tests the moisture absorption rate of resin under high temperature and high humidity conditions.
This article introduces the method of using a hygrothermal test chamber to measure the moisture absorption rate of resin under high temperature and high humidity conditions.
Humidity and Heat Test Chamber for Evaluating Coating Performance under High Temperature and High Humidity Conditions
This article introduces how a humidity and heat test chamber is used to evaluate the performance of coatings in high-temperature and high-humidity environments. Coatings are widely used in industries such as automotive and electronics, but they are prone to issues like reduced adhesion and blistering under actual high-temperature and high-humidity conditions.
Thermal Shock Test Chamber Evaluates Coating Thermal Stability
The thermal shock test chamber simulates sudden temperature changes by rapidly switching between high and low temperature environments, used to evaluate the thermal stability of coatings. In practical applications, coatings may develop internal stresses due to drastic temperature fluctuations, leading to issues such as cracking and peeling.
The necessity of explosion-proof high and low temperature test chambers in lithium battery testing
Lithium batteries pose a risk of thermal runaway or even explosion when tested under extreme temperatures. Explosion-proof high-low temperature test chambers, designed with pressure relief structures, explosion-proof electrical components, and intelligent monitoring systems, can safely release energy and ensure the safety of the testing process.
Tensile Testing Machine Evaluates High and Low Temperature Tensile Properties of Hot Melt Adhesive
This article introduces how to use a tensile testing machine to test the tensile properties of hot-melt adhesives at different temperatures. The performance of hot-melt adhesives varies with temperature: they may soften at high temperatures and become brittle at low temperatures.
The essential difference between thermal shock test chambers and high-low temperature alternating test chambers.
Both thermal shock test chambers and temperature cycling test chambers are used to test the temperature resistance of products, but their core differences lie in the method and purpose of temperature change.