Explosion-proof oil Bath Oven

The explosion-proof oil bath oven evenly transfers heat through thermal oil to heat samples in a confined space. The oil bath medium avoids open flames, making it suitable for drying, curing, or aging tests of flammable and explosive materials. It is commonly used in laboratories in industries such as chemical and coatings for handling volatile substances.
Selection
When selecting, consider matching the sample characteristics with the heating temperature range, ensure the chamber material is corrosion-resistant, verify that the explosion-proof rating meets safety standards, pay attention to temperature control accuracy and uniformity, choose the inner chamber size based on capacity requirements, and check whether the pressure release device and overheat protection functions are complete.

Terms

Standards

Instruments

It adopts explosion-proof composite explosion-proof technology to ensure safe operation. It is equipped with an anti-suction valve to prevent oil from being sucked back. It is equipped with a gas ballast valve to adjust the Vacuum Level. The pumping rate is 24m ³/h, and the noise value is 58dB.

$ 1192.00

Intrinsically safe explosion-proof design, up to CT4 grade, equipped with explosion-proof Sensor and display. Table size 410x510mm, weighing range 110kg, accuracy 10g, stable structure, support external calibrating and a variety of functions.

$ 190.00

Using explosion-proof composite explosion-proof technology, pumping rate of 4L/S, noise only 63dB, equipped with gas ballast valve can remove a small amount of water vapor, safe and reliable for dangerous environment.

$ 701.00

Using explosion-proof composite explosion-proof technology, pumping rate 2L/S, noise as low as 63dB, equipped with gas ballast valve can extract a small amount of water vapor, safe and reliable.

$ 517.00

Using explosion-proof composite explosion-proof technology, pumping rate 8L/S, noise as low as 66dB, equipped with gas ballast valve can extract a small amount of water vapor, suitable for flammable and explosive dangerous places.

$ 1024.00

Adopting explosion-proof, burn-seal, intrinsically safe composite explosion-proof technology, with anti-suction valve and gas ballast valve, the pumping rate is 16m ³/h, the ultimate pressure is 0.005mbar, and the noise value is 58dB (A).

$ 1063.00

The use of explosion-proof composite explosion-proof technology to ensure safe operation, pumping rate of 15L/S and noise only 66dB, equipped with gas ballast valve can handle a small amount of water vapor, compact suitable for use in hazardous environments.

$ 1308.00

The pumping rate is 36m ³/h, the ultimate pressure is 0.005mbar, the anti-suction valve is used to prevent oil from being sucked back, the gas ballast valve can adjust the Vacuum Level and process water vapor, and the composite explosion-proof technology ensures safe operation.

$ 1631.00

The explosion-proof composite explosion-proof technology is used to ensure safe operation, with anti-suction valve and gas ballast valve, the pumping rate is 48m ³/h, and the ultimate pressure is as low as 0.005mbar, which is suitable for dangerous environments.

$ 1889.00

Using explosion-proof composite explosion-proof technology, explosion-proof mark ExdIBT4, pumping rate 90m ³/h, limit pressure as low as 0.005mbar, noise only 58dB, suitable for hazardous environments.

$ 2922.00

Using flameproof composite explosion-proof technology, the pumping rate is 1L/S, the ultimate pressure can reach 0.006mbar, and the noise is as low as 63dB, which is suitable for flammable and explosive environments.

$ 462.00

Adopt compound explosion-proof technology, pumping rate 0.5L/S, noise value 62dB, equipped with gas ballast valve can extract a small amount of water vapor, safe and reliable to adapt to harsh environment.

$ 462.00

Using MCU chip to achieve low power consumption operation, detection error ≤ +/- 3% F. S, Response Time ≤ 30 seconds, support a variety of signal output and wireless transmission, with explosion-proof and explosion-proof structure to ensure safety and reliability.

$ 486.00

Adopt flameproof composite explosion-proof technology to ensure safe operation, equipped with anti-suction valve to prevent oil backflow, pumping rate up to 4m ³/h, limit pressure as low as 0.005mbar, suitable for dangerous environment.

$ 817.00

Using EX-SH784050-100 carbon steel scale body and stainless steel mask, the structure is stable. Range 61kg, Readability 1g, Fast Response Time. With intrinsically safe Explosion-proof level CT4, and standard battery, support no power use.

$ 211.00

Articles

Research on the Stepwise Curing Process of Coatings Using Multi-Stage Temperature Control Ovens
This article investigates a novel process for achieving stepwise curing of coatings using a multi-stage temperature-controlled oven.
Evaluation of thermal aging life of hot melt adhesives using high-temperature oven method
This article introduces a method for evaluating the thermal aging life of hot melt adhesives using a high-temperature oven. The principle is based on the Arrhenius equation, where aging is accelerated by increasing the temperature to simulate performance changes under long-term use.
Thermogravimetric Analyzer for Determining the Solid Content of Coatings
Thermogravimetric analyzers determine the solid content of coatings by monitoring the change in sample mass with temperature, offering faster and more precise results compared to traditional oven methods.
What is the deviation between the moisture meter's rapid moisture measurement and the oven method?
This article primarily compares the differences between rapid moisture analyzers and traditional oven methods in measuring moisture. Understanding these differences helps in using rapid moisture analyzers more appropriately, ensuring data reliability while maintaining efficiency.
Key Technical Points for Determining Paper Moisture Using the 105℃ Oven Method
This article introduces the specific procedure for measuring paper moisture using the 105°C oven method. The process involves placing paper samples into a 105°C oven and drying them until their weight remains constant, then calculating the moisture content based on the weight difference before and after drying.
Oven combined with analytical balance for determination of solid content
This article introduces a method for determining the solid content of samples in the laboratory by combining an oven and an analytical balance.
Temperature gradient control in high-temperature ovens during thermal resistance testing.
The heat resistance test simulates the performance of materials under high temperatures using a high-temperature oven, and the accuracy of its results is highly dependent on the uniformity of temperature inside the oven. If the temperature gradient is poorly controlled, it can lead to uneven heating of samples from the same batch, compromising the validity of the test.
What are the differences between a vacuum oven and a conventional oven?
The main difference between a vacuum oven and a conventional oven lies in their working pressure. Conventional ovens operate at atmospheric pressure, heating through air convection, making them suitable for routine drying tasks. In contrast, vacuum ovens are evacuated to low pressure to reduce air presence, primarily relying on thermal radiation for heat transfer. This makes them ideal for processing heat-sensitive, oxidation-prone materials or those requiring thorough drying.
Natural Convection vs Forced Air Drying: What’s the Difference Between the Two "Schools" of Laboratory Ovens?
This article introduces two drying methods for laboratory ovens: natural convection and forced air drying. What are the differences between them?