Explosion-proof spray-coated glass reactor

The explosion-proof spray-coated glass reactor is coated with an explosion-resistant layer on the outer surface of the glass liner to enhance impact resistance and prevent glass breakage and splattering. It is used for the mixing and reaction processes of flammable and explosive materials such as coatings and inks, ensuring operational safety.
Selection
When selecting an explosion-proof spray-coated glass reactor, it is essential to consider matching the glass material with the corrosiveness of the materials, ensuring the explosion-proof coating is uniform and defect-free, selecting a capacity suitable for the experimental scale, choosing a stirring method that meets mixing requirements, ensuring the temperature and pressure ranges cover the process conditions, and verifying that the interfaces are compatible with existing equipment.

Terms

Standards

Instruments

Intrinsically safe explosion-proof design, up to CT4 grade, equipped with explosion-proof Sensor and display. Table size 410x510mm, weighing range 110kg, accuracy 10g, stable structure, support external calibrating and a variety of functions.

$ 190.00

Using explosion-proof composite explosion-proof technology, pumping rate of 4L/S, noise only 63dB, equipped with gas ballast valve can remove a small amount of water vapor, safe and reliable for dangerous environment.

$ 701.00

Using explosion-proof composite explosion-proof technology, pumping rate 2L/S, noise as low as 63dB, equipped with gas ballast valve can extract a small amount of water vapor, safe and reliable.

$ 517.00

Using explosion-proof composite explosion-proof technology, pumping rate 8L/S, noise as low as 66dB, equipped with gas ballast valve can extract a small amount of water vapor, suitable for flammable and explosive dangerous places.

$ 1024.00

Adopting explosion-proof, burn-seal, intrinsically safe composite explosion-proof technology, with anti-suction valve and gas ballast valve, the pumping rate is 16m ³/h, the ultimate pressure is 0.005mbar, and the noise value is 58dB (A).

$ 1063.00

The use of explosion-proof composite explosion-proof technology to ensure safe operation, pumping rate of 15L/S and noise only 66dB, equipped with gas ballast valve can handle a small amount of water vapor, compact suitable for use in hazardous environments.

$ 1308.00

It adopts explosion-proof composite explosion-proof technology to ensure safe operation. It is equipped with an anti-suction valve to prevent oil from being sucked back. It is equipped with a gas ballast valve to adjust the Vacuum Level. The pumping rate is 24m ³/h, and the noise value is 58dB.

$ 1192.00

The explosion-proof composite explosion-proof technology is used to ensure safe operation, with anti-suction valve and gas ballast valve, the pumping rate is 48m ³/h, and the ultimate pressure is as low as 0.005mbar, which is suitable for dangerous environments.

$ 1889.00

Using explosion-proof composite explosion-proof technology, explosion-proof mark ExdIBT4, pumping rate 90m ³/h, limit pressure as low as 0.005mbar, noise only 58dB, suitable for hazardous environments.

$ 2922.00

Using flameproof composite explosion-proof technology, the pumping rate is 1L/S, the ultimate pressure can reach 0.006mbar, and the noise is as low as 63dB, which is suitable for flammable and explosive environments.

$ 462.00

Adopt compound explosion-proof technology, pumping rate 0.5L/S, noise value 62dB, equipped with gas ballast valve can extract a small amount of water vapor, safe and reliable to adapt to harsh environment.

$ 462.00

Using MCU chip to achieve low power consumption operation, detection error ≤ +/- 3% F. S, Response Time ≤ 30 seconds, support a variety of signal output and wireless transmission, with explosion-proof and explosion-proof structure to ensure safety and reliability.

$ 486.00

Using EX-SH784050-100 carbon steel scale body and stainless steel mask, the structure is stable. Range 61kg, Readability 1g, Fast Response Time. With intrinsically safe Explosion-proof level CT4, and standard battery, support no power use.

$ 211.00

Adopt flameproof composite explosion-proof technology to ensure safe operation, with a pumping rate of 6L/S and a noise of only 64dB. Equipped with a gas ballast valve to handle a small amount of water vapor, it is compact and easy to install and maintain.

$ 817.00

Modular design with low power consumption, intelligent Sensor detection technology, Explosion-proof level Ex db IIC T6 Gb, Protection Rating IP66, support for multiple signal output and wireless transmission.

$ 887.00

Articles

Using a spray coater to achieve the preparation of functionally graded films.
This paper introduces a method for preparing functionally gradient films using a spray coating machine.
Application of Spray Coating Machines in the Encapsulation of Flexible Electronic Devices
This paper introduces the application of spray coating machines in the encapsulation of flexible electronic devices.
Differences in Uniformity Between Spray Coating and Spin Coating Methods
This article compares the differences in uniformity between the spray coating and spin coating methods in the preparation of coatings.
Sand Abrasion Tester for detecting the wear resistance of thermal spray coatings
This article introduces the method of using a sand falling tester to evaluate the wear resistance of thermal spray coatings. Thermal spray coatings are widely used in fields such as machinery and aviation, with wear resistance being a critical performance indicator.
Hall flowmeter measures the flowability of spray powder
This article introduces how a Hall flowmeter measures the flowability of spray powder. It uses a standard funnel to measure the time required for a certain mass of powder to flow out under gravity—the shorter the time, the better the flowability.
Tap density tester evaluates the accumulation characteristics of sprayed powder.
This article introduces how to use a tap density tester to evaluate the packing characteristics of spray powders. The tap density tester simulates vibration to densely pack the powder and measures the mass per unit volume, thereby obtaining the tap density.
Laser particle size analyzer measures the particle size distribution of spray powder.
Laser particle size analyzers measure the particle size distribution of sprayed powder based on the principle of light scattering, which is critical for coating uniformity and adhesion. During measurement, the powder must be dispersed in a suitable medium to avoid agglomeration, and tests should be repeated to ensure accuracy.
Film Coating Machine vs. Spray Gun: The Impact of Different Coating Methods on Coating Performance Evaluation
This article compares two laboratory film preparation methods: the film applicator and the spray gun. The film applicator can produce coatings with uniform thickness and high reproducibility through blade coating, making it suitable for precise formulation studies. The spray gun simulates actual spraying, but the film thickness uniformity is poorer, and the surface may be rougher.
Graphene Transparent Conductive Film Coating Process and Coater Selection
This article introduces the coating processes and coating machine selection for graphene transparent conductive films. The coating processes primarily include blade coating, slot-die coating, spin coating, and spray coating, with choices depending on the properties of the dispersion, the type of substrate, and the production scale.
The role of the coating machine in the preparation of fuel cell membrane electrode assemblies
The film coating machine is a key equipment for preparing the membrane electrode, the core component of fuel cells. It evenly coats a catalyst-containing slurry onto a substrate using techniques such as blade coating, slot-die extrusion, or spraying, forming a catalytic layer ranging from a few micrometers to several tens of micrometers in thickness.
What are some cost-effective alternatives to roll-to-roll coaters for the early stages of flexible film R&D when the investment is too high?
The investment in roll-to-roll coating machines is too high. What are some cost-effective alternatives for the early stages of flexible film research and development? Among blade coating, spin coating, and spray coating, which one would you choose?