Laboratory Lithium Battery Separator Coating Machine

The laboratory lithium battery separator Coater evenly applies slurry onto the surface of the base film using a blade or micro-gravure roll, which is then dried in an oven to form a functional coating. It is used to simulate the battery separator coating process and validate slurry formulations and process parameters. It is suitable for the preparation of functional coatings and process optimization during the research and development phase.
Selection
When selecting, consider the match between the coating width and the substrate, and ensure the coating speed covers the required range for R&D. Focus on the uniformity and precision of coating thickness, and ensure the oven temperature control meets the solvent evaporation requirements. The equipment materials should be resistant to slurry corrosion, and the operation interface should facilitate parameter adjustment and data recording.

Terms

Standards

Instruments

Using High Accuracy Inductance Sensor, Measurement range Ra 0.05-10 μm, built-in lithium battery supports long-term use, with automatic shutdown and metric-to-inch conversion function, portable design weight is only about 420g.

$ 1181.00

The 2900ma large-capacity lithium battery can work for 20 hours, equipped with 2.4-inch high definition color screen and 16-bit data collection chip, supports one-button switching between PPM and mg/m3 units, and has triple alarm function of sound, light and vibration.

$ 687.00

Dual channel LED digital display, using silicon Photocell, photovoltaic cell detection, measurement Repeatability relative standard deviation ≤ 2%, can simultaneously detect various elements of potassium, sodium, lithium, calcium and barium, the sample amount is small and Sensitivity is high.

$ 1493.00

Silicon Photocell, photovoltaic cell detection to ensure accurate and stable measurement, potassium and sodium detection limit of 0.004mmol/L and 0.008mmol/L, support lithium calcium detection function, small sample and Sensitivity.

$ 961.00

Silicon Photocell, photovoltaic cell detection to ensure accurate and stable measurement, can simultaneously detect potassium, sodium, lithium, calcium and barium elements, small sample Sensitivity, with automatic ignition and flameout protection function safe and reliable.

$ 1493.00

Photocell, photovoltaic cell detection to ensure accurate and stable measurement, potassium and sodium detection limit of 0.004mmol/L and 0.008mmol/L, Response Time is less than 8 seconds, support lithium calcium detection function.

$ 904.00

Dual channel LED display, automatic ignition design, using silicon Photocell, photovoltaic cell detection, Sodium Measurement range 0.0-200 mmol/L, Lithium Measurement range 0-15mmol/L, Sensitivity is high and the sample volume is small.

$ 1493.00

Dual-channel LED digital display, Silicon Photocell, photovoltaic cell detection to ensure accurate and stable, potassium, sodium, lithium, calcium and barium multi-element simultaneous detection, Sensitivity is high and the sample amount is small, Linearity ≤ 0.07.

$ 1493.00

Dual channel LED digital display, potassium and sodium detection and have lithium calcium function, using silicon Photocell, photovoltaic cell to ensure measurement Stability, small sample Sensitivity, with flameout protection safety design.

$ 2042.00

Dual channel LED digital display, potassium and sodium can be detected at the same time, lithium calcium function expansion, silicon Photocell, photovoltaic cell detection accuracy is high, Linearity ≤ 0.07, detection limit is as low as 0.004mmol/L, sample volume is small Sensitivity is high, flameout protection is safe and reliable.

$ 1493.00

With 20 °/60 °/85 ° three-angle simultaneous measurement, measurement range of 20 ° up to 0-2000Gs, 2.4-inch color screen and 3000mAh lithium battery, support data storage and Bluetooth connection, Stability is high and portable and durable.

$ 554.00

Silicon Photocell, photovoltaic cell detection to ensure accurate and stable measurement, potassium and sodium can be detected at the same time and have lithium calcium detection function, small sample Sensitivity, Response Time is less than 8 seconds, with flameout protection function safe and reliable.

$ 677.00

Dual channel LED digital display, potassium and sodium can be detected at the same time, lithium calcium detection function, silicon Photocell, photovoltaic cell detection is accurate and stable, the sample amount is small and Sensitivity is high, Linearity ≤ 0.005, detection limit ≤ 0.004.

$ 1493.00

It can directly display six Hardness standards, support 360-degree measurement direction, store 600 sets of data, and operate continuously for 10 hours with lithium battery power supply. It is compact and portable and weighs only 110 grams.

$ 202.00

Dual-channel LED digital display clear reading, button automatic ignition fast and reliable, can simultaneously detect potassium and sodium and support lithium calcium barium measurement, using silicon Photocell, photovoltaic cell detection accuracy, small sample Sensitivity, with flameout protection safety function.

$ 1493.00

Articles

Laboratory rod coater for submicron wet film preparation of photoresist.
This article introduces the process of using a laboratory bar coater to prepare submicron wet films of photoresist.
Application of Perovskite Coater in the Preparation of Intermediate Layers in Tandem Solar Cells
This article introduces the application of perovskite coating machines in the preparation of the intermediate layer of tandem solar cells.
Using a spray coater to achieve the preparation of functionally graded films.
This paper introduces a method for preparing functionally gradient films using a spray coating machine.
Application of Spray Coating Machines in the Encapsulation of Flexible Electronic Devices
This paper introduces the application of spray coating machines in the encapsulation of flexible electronic devices.
Roll-to-Roll Preparation of Perovskite Coaters for Flexible Perovskite Solar Cells
This article introduces the roll-to-roll fabrication method of flexible perovskite solar cells.
Operation Tips for Laboratory-Scale Hot Melt Adhesive Coating Machines
This article introduces the key operational points of a laboratory-scale hot melt adhesive coater. The equipment is primarily used in laboratories to apply hot melt adhesives uniformly onto substrates, supporting the research, development, and testing of adhesives.
Application of Continuous Coating Machine for Lithium Battery Electrode Preparation in Electrode R&D
The laboratory continuous coater is a key piece of equipment in lithium battery electrode research and development, used to simulate mass production coating processes. By precisely controlling parameters such as coating speed, thickness, and tension, it helps researchers optimize slurry formulations and coating procedures.
How to Coat High-Viscosity Slurry – Parameter Setting Tips for Blade Coaters
This article primarily discusses the parameter setting techniques for high-viscosity slurries on blade coaters. High-viscosity slurries exhibit characteristics such as shear thinning, so it is essential to leverage shear effects during coating to facilitate slurry spreading. After coating, the viscosity should recover quickly to prevent sagging.
Common Troubleshooting for Wire Bar Coater: Solving Issues of Streaking and Uneven Thickness
This article mainly introduces solutions to two common faults in the operation of the wire rod coater—coating streaks and uneven coating thickness.
Roll-to-roll coater enables continuous preparation of flexible electronic materials.
Roll-to-roll coating is a continuous production process that involves uniformly applying functional slurry onto a flexible substrate, followed by drying and curing to form a functional film.
What are some cost-effective alternatives to roll-to-roll coaters for the early stages of flexible film R&D when the investment is too high?
The investment in roll-to-roll coating machines is too high. What are some cost-effective alternatives for the early stages of flexible film research and development? Among blade coating, spin coating, and spray coating, which one would you choose?
Coating Process of Slurries with Different Viscosities on Vacuum Adsorption Coating Machines
This article explores the process adaptability of slurries with different viscosities on vacuum adsorption coating machines. The slurries are categorized into low, medium, and high viscosity, and their flow characteristics during the coating process, along with key process control points, are discussed respectively.
The working principle of laboratory wire rod coaters and methods for controlling coating thickness
The laboratory wire rod coater is a precision instrument used to prepare uniform, thickness-controllable wet film coatings on substrate surfaces. Its core components include a coating rod, a flat coating platform, clamps for securing the substrate, and a mechanical system that drives the coating rod to move at a constant speed.